Hacking ISP for free internet or Bypass ISP Login Page!

On By Bright Joe

Hello dudes,

In this particular post, I m gonna share with you an awesome trick to bypass your ISP login page and gain internet access for free. This trick is work on all WAN networks except Dial-up networks. Networks which uses a username and password to connect are known as PPPoE will not work with this trick because every client uses a different username and password. But it will work on Static IP and DHCP networks!

I have written an updated article on this topic which you should read if you want to see everything in action and step-by-step.

For Dial-Up users-
Try this post: GETTING UNLIMITED FREE INTERNET ON DIAL-UP NETWORKS!

Required Software:

Netcut: This is a software which finds IPs and MAC or Physical addresses of the connected clients in your network. There are hundreds of users and sometimes thousands in a particular ISP. This software has a user-friendly interface which is quite easy for beginners.

Steps for Getting Free Internet!

  1. Download Netcut
  2. Install Netcut and run it.
  3. Now, you have to allow perhaps 10 seconds for the software to scan the connected clients and show their information.
  4. Now, as mention earlier that it will only work on DHCP and Static IP networks. You have to choose any one client and copy down it’s MAC Address and IP address in Notepad.
  5. Now we will have to change our computer’s Physical address and IP address. First of all, you have to go to Network and Sharing Center. Then click on Change Adapter Settings and right click on your adapter name and then click on Properties.
  6. Now click on Configure and move to Advanced tab. Then look for Network Address in the list, and then you will find that it is set to Not Present. Now tick or check Value and type the MAC address you copied from Netcut. This will restart your adapter, so wait 10 seconds until it reconnects properly.
  7. Now, it’s time to apply the IP we copied from Netcut. Now right click on your adapter name and click on Internet Protocol Version 4 (TCP/IPv4) and click on Properties. Now click on Use the following IP address.
    Fill the blanks like this:
    IP Address: Put the IP you got from Netcut.
    Subnet Mask: Use the same subnet mask you got from your ISP.
    Default Gateway: Use the same gateway IP you got from your ISP.
    To find the Subnet mask and Default gateway, you have to open up Command Prompt and type this command: IPCONFIG and you will find the subnet mask and gateway.

Congrats: You now have a free internet connection!
Note: If one client is not working, use another!

You can also visit my latest blog where I post weekly for the latest gaming and tech tips.

How does it Work?

For example, you are trying to access Google but when you press enter, instead of going to Google, it will redirect you to the ISP login page or ISP Website. So when you change your MAC and IP addresses, you change your identity and you get access to the internet.

This trick can also speed up your internet. If the client you choose is from a big company and uses an internet package which has a greater speed, you will get the same speed as they get.

I think, this post will help you with getting free internet.

If you are using a Router

Hey guys, I got a huge number of questions on how to apply this on routers because routers have become a common device which almost 90% of the Internet users use. Well, I tried this and succeeded. Let’s see how you can do this on your Router.

I have written a recent blog post on how to boost WiFi signal using a DIY WiFi extender. This usually helps boost your Internet speed significantly if you’re using a router.

I don’t know all the router’s interface but this option is known as MAC Clone. You can change your MAC address to the address you found on Netcut. Also change your router connection setting to Static IP if it’s set to DHCP. You have to set the IP as shown above. I hope that will help because it worked for me and I was enjoying the free internet with my family. 😀

SHARING is CARING! 😀

Please share if I could help you and let your friends know.
Don’t forget to comment below and if you face any problems, write them below and I will leave a reply and get something new for you! 😉

 

159 thoughts on “Hacking ISP for free internet or Bypass ISP Login Page!”

  3. sam

    lol if did ths its only 90% right but when u long in google page ths isp log in page is open and u hv to must be entered ur user name and password whch is given by isp to their user ! and user name password its only know the real user u dont knw ! 😛 😛

    Like

    Reply

    1. Yeah, you hack it with Cain which ARP poisons a particular network and gives you all their usernames and password if they login during the ARP poisoning state. I will soon write about it.

      Like

      Reply
  4. sam

    and one more thing u dont need to any additional software u can find lan network user ip and mac address with help dos command ! 😉

    Like

    Reply
  5. michael

    bro the trick works fine until n unless d user has logged out … after that it redirects back 2 d isp page to provide login details.
    i wanna knw if tht user password can be pulled out so as i can login back ? maybe nt possible idk… but if u knw please provide with d steps it wud b great addition 2 d trick
    i have kali linux installed 🙂

    Like

    Reply

  6. Brilliant but there’s a problem say i managed to make this work , what about the other user will he and i get disconnected for exceeding the limited quota i’d love to know if so , is there any other way to hack my own account on their system because i don’t wanna do that to people and also any ideas on how to get high bandwidth

    Like

    Reply
  11. Navil

    I have been using this method for the past 2 years but only get 60 kbps download speed do u know any ways to increase that or any ways to access radius manager billing system which my ISP uses.

    Like

    Reply
  21. Azhar

    Great article, I have a situation, If i don’t even know the subnet of ip. can i find that??I mean my ISP allocated me static ip, but then discontinued my connection for some reason. But with cain i tried scan 172.172.0.0 255.255.0.0. and found i valid ip address and used for 6 months. Now 172.172…subnet has been deleted by him, the again by luck i get a valid ip for 168.168….But now i can’t get any valid ip. Can u suggest. Thanks

    Like

    Reply

    1. Bro, if your network uses Static IP, simply change your IP to the client’s IP and also the MAC address you found. It would work then, remember to unplug your router first or else no clients will be detected.

      Like

      Reply
  22. vivek pandey

    Hello
    In my case I know my user name and password given by isp but it work on my office router can i use this same username and password to my home router both have same broadband (hns) ..
    How make colons of routers please help me…

    Like

    Reply
  25. jamai

    can you plz tell me an alternative software to Netcut….I can’t run it on my windows 7. Im getting runtime error.BTW how can you find MAC if you know the external IP from same ISP?

    Like

    Reply

Leave a comment